U
DVD PLAYER
LECTEUR DE DVD
DVD-S661
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications
not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices.
Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference
will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning
the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6660 Orangethorpe
Ave. Buena Park, CA90622.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion - and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries
Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume
levels.
For Customer Use:
Read carefully the information located at the rear
panel of this unit and enter below the Serial No.
Retain this information for future reference.
Model No.
Serial No. __________________________
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
AVOID DIRECT EXPOSURE TO THE BEAM
INVISIBLE LASER RADIATION WHEN OPEN
DANGER:
AVERTISSEMENT
DO NOT STARE INTO BEAM
INVISIBLE LASER RADIATION WHEN OPEN
CAUTION:
L’utilisation de commandes et l’emploi de réglages
ou de méthodes autres que ceux décrits ci-dessous,
peuvent entraîner une exposition à un rayonnement
dangereux.
PRECAUCIÓN
El uso de los controles, los ajustes o los
procedimientos que no se especifican enste manual
pueden causar una exposición peligrosa a la
radiación.
ii
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
1
2
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a well ventilated, cool, dry, clean
place — away from direct sunlight, heat sources,
vibration, dust, moisture, or cold. In a cabinet, allow
about 2.5 cm (1 inch) of free space all around this
unit for adequate ventilation.
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
Do not expose this unit to sudden temperature
changes from cold to hot, nor locate this unit in an
environment with high humidity (i.e., a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage
to this unit, and/or personal injury.
14 When not planning to use this unit for long periods
of time (i.e., vacation), disconnect the AC power
plug from the wall outlet.
15 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that
this unit is faulty.
16 Before moving this unit, press STANDBY/ON to
set the unit in standby mode, then disconnect the
AC power plug from the wall outlet.
17 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
3
4
18 The batteries shall not be exposed to excessive heat
such as sunshine, fire or the like.
The unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed
to consume a very small quantity of power.
5
Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit
may be exposed to liquid dripping or splashing. On
the top of this unit, do not place:
–
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e., candles), as they may
cause fire, damage to this unit, and/or
personal injury.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug
to wide slot and fully insert.
This Class B digital apparatus complies with
Canadian ICES-003.
–
–
Containers with liquid in them, as they may
fall, spilling the liquid and causing an electrical
shock to the user and/or damage to this unit.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
6
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
Do not use excessive force on switches, knobs and/
or cords.
7
8
9
LASER SAFETY
This unit employs a laser. Due to possible eye injury,
only a qualified service person should remove the cover
or attempt to service this device.
DANGER
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
This unit emits visible laser radiation when open. Avoid
direct eye exposure to beam.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using
this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit,
and/or personal injury. Yamaha will not be held
responsible for any damage resulting from use of
this unit with a voltage other than as specified.
13 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reason.
When this unit is plugged into a wall outlet, do not
place your eyes close to the opening of the disc tray and
other openings or look inside.
iii
Contents
Introduction ..................................3 Playback Operation ................... 15
Supplied accessories .................................3
Region codes ..............................................3
Playable disc formats .................................3
Cleaning discs .............................................4
Patent information ......................................4
Basic operation ......................................... 15
Selecting a track/chapter ..................................15
Searching backward/forward ...........................15
Repeat/Shuffle functions ......................... 15
Repeat/Shuffle playback ..................................15
Repeating a section within a chapter/track ......16
Operations for video playback
(DVD/VCD/SVCD) ...................................... 16
Using the disc menu .........................................16
Playback in slow motion ..................................16
Zooming pictures in/out ...................................16
Resuming playback from the last
Functional Overview ....................5
Front panel ..................................................5
Rear panel ....................................................6
Remote control ............................................7
stopped point ....................................................16
Using the on-screen display (OSD) .................17
Special DVD features ............................... 18
Playing by title .................................................18
Selecting an audio language/format
Connections ..................................8
General notes on connections ..................8
Audio connections ......................................8
Digital connection ..............................................8
Analog connection ..............................................8
Video connections ......................................9
Component video jacks <A> ..............................9
S-video jack <B> ................................................9
Composite video jack <C> .................................9
HDMI connection .......................................10
HDMI jack ........................................................10
Other connections ....................................11
USB port ...........................................................11
Remote control jacks ........................................11
and subtitle language ........................................18
Special VCD/SVCD features ..................... 18
Using the playback control (PBC) menu .........18
Playing data discs (MP3/WMA/
JPEG/DivX) ................................................ 18
Selecting a folder and track/file .......................19
Special picture disc features ................... 19
Using the preview function ..............................19
Zooming pictures in/out ...................................19
Playback with multi-angles ..............................20
Playing MP3 music and JPEG picture
Getting Started ...........................12
Step 1: Inserting batteries into
simultaneously .................................................20
Special DivX features ............................... 20
Using the interactive menu ..............................20
Selecting an audio/subtitle language ................20
Using a USB device .................................. 21
Supported USB devices ...................................21
Playing data files ..............................................21
the remote control ....................................12
Using the remote control ..................................12
Step 2: Turning on the power ..................12
Step 3: Setting a TV type/display and
language ....................................................13
Setting a color system for your TV ..................13
Setting an aspect ratio for your TV ..................13
Setting the OSD language ................................14
Setting the audio, subtitle and disc menu
languages (DVD-Video only) ..........................14
1 En
Contents
Setup Menu .................................22 Language Codes ........................ 35
General setup menu .................................22
Locking/Unlocking the disc for viewing ..........22
Troubleshooting ......................... 36
Dimming the front panel display ......................22
Programming disc tracks (except MP3/
Glossary ...................................... 39
WMA/JPEG/DivX) ..........................................22
OSD language ..................................................23
Specifications ............................. 41
Setting the screen saver ....................................23
Setting the sleep timer ......................................24
Setting the auto standby function .....................24
Displaying the DivX® VOD
registration code ...............................................24
Audio setup menu .....................................25
Setting the analog output ..................................25
Setting the digital output ..................................25
Turning the HDMI audio on/off .......................26
Turning the night mode on/off .........................26
Setting the lip synchronization .........................27
Video setup menu .....................................27
TV type .............................................................27
Setting the TV display ......................................27
Turning the progressive scan function on/off ...28
Adjusting picture settings .................................29
Turning the black level on/off...........................29
Turning the closed caption on/off .....................30
Setting the HDMI video ...................................30
Preference setup menu ............................31
Audio, subtitle and disc menu ..........................31
Restricting playback with parental control .......31
Selecting playback of VR format .....................32
Selecting the MP3/JPEG menu ........................32
Displaying DivX external subtitle files ............33
Selecting the PBC (playback control)
function .............................................................33
Changing the password ....................................34
Resetting the system .........................................34
2 En
Introduction
Introduction
Thank you for purchasing this unit. This
owner’s manual explains the basic operation
of this unit.
This manual is printed prior to production.
Design and specifications are subject to
change in part as a result of improvements,
etc. In case of differences between the manual
and the product, the product has priority.
T
Playable disc formats
This unit is designed for use with discs having
the logos shown below. Do not attempt to load
any other type of disc into this unit.
Supplied accessories
• Remote control
• Two batteries (AAA, R03, UM-4) for the
remote control
• Audio/Video pin cable
• Owner’s manual
This unit can play:
• DVD-R/RW/R DL and DVD+R/RW/R DL
discs recorded in DVD-Video compatible
format
• DVD-RW discs recorded in VR format
(compatible with CPRM)
• MP3, WMA and JPEG files recorded on
CD-R/RW, DVD-R/RW, DVD+R/RW and
USB
Region codes
This unit is designed to support the region
management system. Check the regional code
number on the DVD disc package. If the
number does not match the region code of this
unit (see the table below or the back of this
unit), this unit may be unable to play the disc.
• KODAK picture CDs, FUJICOLOR CDs
• ISO 9660 Level1/Level2 for CD-R/RW
•
Up to 298 folders per disc/USB device and up
to 648 files per folder with up to 8 hierarchies
®
• DivX files recorded on CD-R/RW,
DVD-R/RW, DVD+R/RW and USB
– Official DivX® Ultra Certified product
– Plays all versions of DivX® video (including
DivX® 6) with enhanced playback of DivX®
media files and the DivX® Media Format
Region
Playable
discs
Destination
code of
this unit
U.S.A.,
Canada
ALL
1
2
3
4
1
2
3
4
Notes
U.K.,
Europe
•
CD-R/RW, DVD-R/RW/R DL and DVD+R/RW
R DL cannot be played unless finalized.
Progressive JPEG and copyright-protected WMA
files cannot be played with this unit.
Only the first session of DVD-R/RW/R DL and
DVD+R/R DL can be played.
Some discs cannot be played depending on disc
characteristics or recording conditions.
Do not use any non-standard shaped discs
(heart-shaped, etc.).
/
ALL
ALL
ALL
•
•
•
•
•
•
Asia,
Korea
Australia,
Central and
South America
Do not use discs with tape, seals, paste or many
scratches on their surface.
For details about playable formats, see
“Specifications” on page 41.
3 En
Introduction
Cleaning discs
• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out.
Do not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic
spray intended for analog records.
Patent information
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are registered trademarks of DTS, Inc.
DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, Inc. and are used under license.
HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
4 En
Functional Overview
Functional Overview
Front panel
1
2
3 4 5
6
7 8 9
0
1 STANDBY/ON
6 Front panel display
Shows the current status of this unit.
Turns on this unit or sets it to the standby mode.
2 Disc tray
Loads a disc in the disc tray.
7 PLAY ( p)
Starts playback.
3 OPEN/CLOSE (
)
8 PAUSE (
)
Opens or closes the disc tray.
Pauses playback.
4 HDMI indicator
9 STOP ( s )
Lights up when an HDMI component is
connected, and signals output via the HDMI
jack of this unit.
Stops playback.
0 USB port
Connect to the USB port of your USB device
5 PROGRESSIVE indicator
Lights up when this unit enters the progressive
mode.
(see page 11).
5 En
Functional Overview
Rear panel
COMPONENT
VIDEO
PR
Y
REMOTE CONTROL
OUT
IN
COAXIAL
PB
S VIDEO
HDMI
AUDIO OUT
DIGITAL OUT
VIDEO OUT
1
2
3
4
5
6 7 8
1 AC power cable
5 DIGITAL OUT - COAXIAL jack
Connect to the coaxial input jack of your AV
receiver (see page 8).
Plug the power cable into the AC wall outlet.
2 REMOTE CONTROL (IN, OUT) jacks
Connect the REMOTE CONTROL (IN) jack of
this unit to the remote control output jack of
your Yamaha AV receiver.
6 VIDEO OUT - COMPONENT (Y, PB, PR)
jacks
Connect to the component input jacks of your
Connect the REMOTE CONTROL (OUT) jack
of this unit to the remote control input jack of
your Yamaha component (see page 11).
AV receiver (see page 9).
7 VIDEO OUT - S VIDEO jack
Connect to the S-video input jack of your AV
receiver (see page 9).
3 HDMI jack
Connect to the HDMI input jack of your HDMI
component (see page 10).
8 VIDEO OUT - VIDEO jack
Connect to the composite video input jack of
your AV receiver (see page 9).
4 AUDIO OUT (L, R) jacks
Connect to the audio input jacks of your AV
receiver or stereo system (see page 8).
Caution: Do not touch the inner pins of the jacks on the rear panel of this unit.
Electrostatic discharge may cause permanent damage to this unit.
6 En
Functional Overview
Remote control
5 l22
Moves to the previous chapter or track.
Searches backward.*
6
7
Stops playback.
Opens the disc tray.*
1
2
0
7 Numeric buttons (0-9)
Selects numbered items in the currently
displayed menu.
3
8 SUBTITLE
Selects the subtitle language (see pages 18 and
20).
4
5
6
q
w
e
r
9 ZOOM
Enlarges the video image (see pages 16 and 19).
0 ON SCREEN
7
Accesses or exits from the on-screen display
(OSD) menu of this unit (see page 17).
t
y
u
8
9
q SET UP
Accesses or exits from the setup menu of this
unit (see pages 13 and 22).
w 33l
Moves to the next chapter or track.
Searches forward.*
1
e 3/8
Turns on this unit or sets it to the standby mode.
Starts or pauses playback.
2 TOP MENU/RETURN
r USB
Displays the top-level disc menu (DVD).
Moves back to the previous menu (DVD*/VCD)
(see page 18).
Accesses the contents of the connected USB
device or exits from the USB mode (see
page 21).
3 2 / 3/5/a
t AUDIO
Selects an item in the currently displayed menu.
Search or slow playback.
Selects the audio language or format (see
pages 18 and 20).
ENTER
Confirms the menu selection.
y REPEAT
Accesses or exits from the repeat/shuffle mode
(see page 15).
4 MENU
Displays the menu of a disc (DVD/JPEG)
(see pages 16, 18, 19 and 20).
Switches PBC on or off (VCD) (see page 18).
u REPEAT A-B
Repeats a specific segment (see page 16).
* Press and hold the button for about two seconds.
7 En
Connections
Connections
Notes
General notes on connections
•
You need to set [DIGITAL OUTPUT] to [ALL]
Be sure to turn off this unit and unplug the
power cable before you make or change
connections.
• Depending on the component you want to
connect, there are various ways to make
connections. Possible connections are
described below.
• Refer to the manuals supplied with your
other components as necessary to make the
best connections.
• Do not connect this unit via your VCR. The
video quality could be distorted by the copy
protection system.
(see “DIGITAL OUTPUT” on page 25).
If the audio format of the digital output does not
match the capabilities of your receiver, the
receiver produces a distorted sound or no sound
at all. Make sure to select the appropriate audio
format from the menu screen on the disc.
Pressing AUDIO on the remote control once or
more may change not only the audio languages
but also the audio format. The selected format
appears in the front panel display for several
seconds.
•
•
If you want to enjoy Dolby Digital, DTS and
MPEG formats, you must connect this unit to an
AV receiver that supports these formats.
• Do not connect the audio out jack of this unit
to the phono in jack of your audio system.
Analog connection
This unit has 2-ch analog output jacks.
Connect the AUDIO OUT (L, R) jacks of this
unit to the corresponding input jacks of your
audio component (such as a stereo amplifier)
using the supplied audio pin cable.
Audio connections
Digital connection
This unit has a digital coaxial output jack.
Connect the DIGITAL OUT - COAXIAL jack
of this unit to your AV receiver equipped with
a Dolby Digital, DTS, or MPEG decoder
using a commercially available coaxial cable.
COMPONENT
VIDEO
PR
Y
COAXIAL
PB
S VIDEO
AUDIO OUT
DIGITALOUT
VIDEO OUT
This unit
L
R
COMPONENT
VIDEO
PR
Y
Audio pin cable
(supplied)
L
R
COAXIAL
PB
S VIDEO
AUDIO OUT
DIGITAL OUT
VIDEO OUT
Stereo
amplifier
This unit
C
C
L
R
AV receiver
Speakers
Speakers
8 En
Connections
Component video jacks <A>
Video connections
Component video connections achieve higher
fidelity color reproduction than S-video
connections by transmitting video signals on
separate wires for luminance (Y: green) and
chrominance (PB: blue, PR: red).
Connect the VIDEO OUT - COMPONENT
(Y, PB, PR) jacks of this unit to component
input jacks of your AV receiver and then to
those of your TV using a commercially
available component cable. Observe the color
of each jack when you make connections.
If your receiver does not have component
output jacks, you can achieve a better video
image by connecting the component output
jacks of this unit directly to the component
input jacks of your TV.
If your AV receiver has video output jacks,
connect your receiver and then your TV so
that you can use one TV for several different
video sources (LD, VCR, etc.) by simply
switching the input source selector of your
receiver.
This unit has several types of video output
jacks. Use the one that corresponds to the
input jacks of the component to be connected.
COMPONENT
VIDEO
PR
Y
COAXIAL
PB
S VIDEO
AUDIO OUT
DIGITAL OUT
VIDEO OUT
This unit
S
PR
PB
Y
V
V
Video pin
cable
(supplied)
<A>
<B>
<C>
S-video jack <B>
S-video connections achieve a clearer picture
than composite video connections by
PR
PB
Y
S
PR
PB
Y
transmitting video signals on separate wires
for luminance (Y) and chrominance (C).
Connect the VIDEO OUT - S VIDEO jack of
this unit to an S-video input jack of your AV
receiver and then to that of your TV using a
commercially available S-video cable.
COMPONENT
VIDEO IN
S VIDEO
INPUT
VIDEO
INPUT
AV receiver
VIDEO
OUT
COMPONENT S VIDEO
VIDEO OUT OUT
VIDEO
IN
COMPONENT S VIDEO
VIDEO IN
IN
Composite video jack <C>
TV
Connect the VIDEO OUT - VIDEO jack of
this unit to a video input jack of your AV
receiver and then to that of your TV using the
supplied video pin cable.
9 En
Connections
Notes
HDMI connection
•
You need to set [HDMI AUDIO] (see page 26)
and [HDMI VIDEO] (see page 30).
HDMI jack
HDMI provides high quality digital audio and
video on a single connection.
•
You need to make an appropriate audio
connections if the connected component does not
output audio signals (see “Audio connections” on
page 8).
This unit is not compatible with HDCP-
incompatible HDMI or DVI components.
You need a commercially available HDMI/DVI
conversion cable when you connect this unit to
other DVI components. In this case, the HDMI
jack of this unit does not output any audio
signals.
Depending on the connected DVI component,
black and white in the image may not be distinct.
In that case, adjust the picture setting of the
connected DVI component.
Do not disconnect or turn off the power of the
HDMI/DVI component connected to the HDMI
jack of this unit while data is being transferred.
Doing so may disrupt playback or cause noise.
When connecting an HDMI component, refer to
the manual supplied with your component.
Connect the HDMI jack of this unit to an
HDMI input jack of your AV receiver, and
then to that of your TV using a commercially
available HDMI cable.
If your receiver does not have an HDMI input
jack, you can achieve a better video image by
connecting the HDMI jack of this unit directly
to the HDMI input jack of your TV.
This unit can display High-Definition JPEG
images (720p or 1080i) when you connect this
unit to an HDTV via the HDMI jack. For
details, see “HD JPEG” on page 31.
•
•
•
•
•
COMPONENT
VIDEO
PR
Y
COAXIAL
PB
S VIDEO
HDMI
AUDIO OUT
DIGITALOUT
VIDEO OUT
This unit
HDMI cable
HDMI IN
AV receiver
HDMI OUT
HDMI IN
TV
10 En
Connections
Remote control jacks
Other connections
This unit has remote control input/output
jacks. If your AV receiver is a Yamaha product
and has the capability to transmit of SCENE
control signals, you can use the SCENE
function.
Connect the REMOTE CONTROL (IN) jack
of this unit to a remote control output jack of
your receiver using a commercially available
monaural mini-jack cable so that this unit
starts playback automatically by simply
pressing a button of your receiver.
USB port
This unit has a USB port and can access MP3,
WMA, DivX and JPEG files saved on your
USB device.
Connect the USB port on the front panel of
this unit to a USB port of your USB device.
REMOTE CONTROL
This unit
OUT
IN
HDMI
USB
device
This unit
REMOTE OUT
Notes
AV receiver
•
•
This unit may not recognize some USB devices.
For details about the USB features, see “Using a
USB device” on page 21.
Note
For details about the SCENE function, refer to the
owner’s manual supplied with your Yamaha AV
receiver.
11 En
Getting Started
Getting Started
Using the remote control
Step 1: Inserting batteries into
the remote control
Use the remote control within 6 m
(approximately 20 ft) of this unit and point it
toward the remote control sensor.
3
1
Within 6 m
(approximately 20 ft)
2
1 Open the battery compartment.
2 Insert the two supplied batteries (AAA,
R03, UM-4) following the indications
(+/–) inside the compartment.
Notes
•
Do not spill water or other liquids on the remote
control.
3 Close the cover.
•
•
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
Notes
•
Insert batteries correctly according to the polarity
markings (+/–). Batteries inserted in the opposite
orientation may leak.
– places of high humidity, such as near a bath
– places of high temperature, such as near a
heater or stove
– places of extremely low temperature
– dusty places
•
•
•
Replace the exhausted batteries immediately with
new ones to prevent leakage.
Remove the batteries from the compartment if the
remote control is not used for more than a month.
If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material
or letting it come into contact with clothing, etc.
Clean the battery compartment thoroughly before
installing new batteries.
•
When the remote control works unstably, point it
at an angle upward to the sensor.
Step 2: Turning on the power
1 Plug the power cable into the AC outlet.
2 Turn on your TV and AV receiver.
•
•
Do not use old batteries together with new ones.
Do not use different types of batteries (such as
alkaline and manganese batteries) together. Read
the packaging carefully as these different types of
batteries may have the same shape and color.
Dispose of the batteries correctly in accordance
with your local regulations.
3 Select the appropriate input source of the
AV receiver (refer to the manual supplied
with your AV receiver).
•
4 Press STANDBY/ON on the front panel or
on the remote control to turn on this
unit.
➜ The front panel display lights up.
5 Set the TV to the correct video input (refer
to the manual supplied with your TV).
➜ The default screen appears on the TV.
12 En
Getting Started
NTSC
Step 3: Setting a TV type/display
and language
Select this if the connected TV is an NTSC
system TV. It will change the video signals of
PAL discs and output them in NTSC format.
You can customize this unit using the setup
menu displayed on the TV screen.
MULTI
Select this if the connected TV is compatible
with both NTSC and PAL formats (such as a
multi-system TV).
The output format will be in accordance with
the video signals of the disc.
Notes
•
Unless stated otherwise, all operations described
here are carried out using the supplied remote
control.
5 Select an item, and then press ENTER.
•
•
To return to the previous menu, press 2.
To exit from the menu, press SET UP.
Notes
Setting a color system for your TV
•
•
•
Before changing the current TV standard setting,
ensure that your TV supports the selected TV
type.
If the picture is not displayed properly on your
TV, wait for 15 seconds for this unit to activate
automatic recovery.
This unit is compatible with both NTSC and
PAL video formats. Select the color system
that matches your TV.
When making HDMI connections, you cannot
change or select [TV TYPE].
VIDEO SETUP PAGE
TV TYPE
PAL
TV DISPLAY
NTSC
MULTI
PROGRESSIVE
PICTURE SETTING
BLACK LEVEL
CLOSED CAPTION
HDMI SETUP
CHANGING NTSC TO PAL :
1. ENSURE THAT YOUR TV SUPPORTS
PAL STANDARD.
2. IF THERE IS A DISTORTED PICTURE
DISPLAYED ON THE TV, WAIT 15
SECONDS FOR AUTO RECOVER.
1 Press SET UP.
OK
CANCEL
2 Press 3 repeatedly to select “VIDEO
SETUP PAGE”.
3 Press 5/a to highlight [TV TYPE], and
then press 3.
Setting an aspect ratio for your TV
You can set the aspect ratio of this unit to
match your TV. If the aspect ratio of your TV
is 4:3, you do not need to change this setting.
If you have a widescreen TV, change this
setting according to the procedure below.
For details, see “Setting the TV display” on
page 27.
4 Press 5/a to highlight one of the
following options.
PAL
Select this if the connected TV is a PAL
system TV. It will change the video signals of
NTSC discs and output them in PAL format.
13 En
Getting Started
Setting the audio, subtitle and disc
menu languages (DVD-Video only)
VIDEO SETUP PAGE
TV TYPE
You can select your own preferred language
for the audio, subtitle and disc menu. This unit
automatically switches to the selected
language whenever you load a disc. If the
selected language is not available on the disc,
the default language of the disc will be used
instead.
TV DISPLAY
4:3 PAN SCAN
PROGRESSIVE
PICTURE SETTING
BLACK LEVEL
CLOSED CAPTION
HDMI SETUP
4:3 LETTER BOX
16:9
1 Press SET UP.
2 Press 3 repeatedly to select “VIDEO
PREFERENCE PAGE
SETUP PAGE”.
AUDIO
ENGLISH
SUBTITLE
DISC MENU
PARENTAL
VR LIST
CHINESE (SIMP)
FRENCH
3 Press 5/a to highlight [TV DISPLAY],
and then press 3.
4 Press 5/a to highlight [16:9], and then
press ENTER.
SPANISH
PORTUGUESE
POLISH
MP3/JPEG NAV
DIVX SUBTITLE
PBC
ITALIAN
TURKISH
Setting the OSD Language
1 Press
7
twice, and then press SET UP.
You can select your own preferred language
for the setup menu. This setting remains once
selected.
2 Press 3 repeatedly to select
“PREFERENCE PAGE”.
3 Press 5/a to highlight one of the options
below, and then press 3.
•
•
•
AUDIO (audio language)
SUBTITLE (subtitle language)
DISC MENU (disc menu language)
GENERAL SETUP PAGE
DISC LOCK
DISPLAY DIM
PROGRAM
OSD LANGUAGE
SCREEN SAVER
SLEEP
ENGLISH
ESPAÑOL
FRANÇAIS
4 Press 5/a to select a language, and then
press ENTER.
AUTO STANDBY
DIVX(R) VOD CODE
5 Repeat steps 3-4 for other language
settings.
1 Press SET UP.
■ To select a language not in the list
2 Press 2 / 3 to select “GENERAL SETUP 1 Select [OTHERS] in [AUDIO] or
PAGE”.
[SUBTITLE] or [DISC MENU].
3 Press 5/a to highlight [OSD
LANGUAGE], and then press 3.
4 Press 5/a to select a language, and then
press ENTER.
2 Use the numeric buttons (0-9) to enter
the 4-digit language code (see “Language
Codes” on page 35), and then press
ENTER.
14 En
Playback Operation
Notes
Playback Operation
Selecting a track/chapter
1 Press l22 / 33l or use the numeric
buttons (0-9) to select a track/chapter
number.
•
If the prohibited icon ( ) appears on the TV
screen when a button is pressed, the function for
that button is not available on the current disc or
at the current time.
Unless stated otherwise, all operations described
here are carried out using the supplied remote
control.
Depending on the disc, some operations may
operate differently or be restricted. Refer to the
instruction supplied with the disc.
Do not push on the disc tray or put any objects
other than discs on the disc tray. Doing so may
cause this unit to malfunction.
2 During repeated playback, press l22 /
33l to replay the same track/chapter.
•
•
•
Searching backward/forward
1 Press and hold l22 / 33l or press 2 / 3.
2 While searching, press l22 / 33l or
2 / 3 repeatedly to select the desired
speed.
3 To resume normal playback, press 3/8 .
Basic operation
Notes
1 Make sure this unit is turned on.
•
The 2 / 3 key may not be available with some
discs.
For MP3 and WMA, the search function allows
you to search the track currently being played.
2 Press OPEN/CLOSE ( ) on the front
•
panel to open the disc tray.
3 Place the disc in the disc tray with the
printed side up.
Repeat/Shuffle functions
4 Press OPEN/CLOSE ( ) again to close
the disc tray.
➜ After recognizing the disc, this unit
starts playback automatically.
Repeat/Shuffle playback
Each time you press REPEAT during
playback, the front panel display changes
as follows:
•
If you press 3/8 when the disc tray is
open, the disc tray closes and playback
starts automatically.
DVD
5 To pause playback, press 3/8 during
➜ RPT ONE (repeat chapter)
➜ RPT TT (repeat title)
➜ RPT ALL (repeat all)
➜ SHUFFLE (shuffle)
➜ RPT SHF (shuffle repeat)
➜ RPT OFF (repeat off)
playback.
➜ Playback is paused and the sound is
muted.
•
Frame-by-frame playback can be done
by pressing PAUSE ( ) on the front
panel repeatedly.
VCD/SVCD/CD
➜ RPT ONE (repeat track)
➜ RPT ALL (repeat all)
➜ SHUFFLE (shuffle)
➜ RPT SHF (shuffle repeat)
➜ RPT OFF (repeat off)
6 To resume normal playback, press 3/8
again.
7 To stop playback, press
7
.
15 En
Playback Operation
MP3/WMA/DivX
Playback in slow motion
You can play back video in slow motion.
➜ RPT ONE (repeat track)
➜ RPT FLD (repeat folder)
➜ SHUFFLE (shuffle)
➜ RPT OFF (repeat off)
1 Press 5 for reverse slow motion or a for
forward slow motion.
2 During slow motion, press 5/a repeatedly
Note
to select the desired speed.
For VCD, repeat playback is not available when the
PBC mode is on.
3 To resume normal playback, press 3/8 or
ENTER.
Repeating a section within a
chapter/track
Note
For VCD and SVCD, reverse slow motion is not
available.
1 While playing a disc, press REPEAT A-B
at the desired starting point.
➜ “SET A” appears in the front panel
display.
Zooming pictures in/out
You can enlarge or shrink the picture on the
TV screen and pan through the enlarged
picture.
2 Press REPEAT A-B again at the desired
end point.
•
A and B can only be set within the same
chapter/track.
1 During playback, press ZOOM repeatedly
to display the picture at different scales.
➜ “RPT AB” appears in the front panel
display and the selected section repeats
continuously.
•
Use 2 / 3/5/a to pan through the
enlarged picture.
➜ Playback continues.
3 To exit from the sequence, press REPEAT
A-B.
2 Press ZOOM repeatedly to return to the
original size.
Resuming playback from the last
stopped point
You can resume playback of the last ten discs,
even if the discs were ejected or the power of
this unit was turned off.
Operations for video playback
(DVD/VCD/SVCD)
Using the disc menu
Depending on the disc, a menu may appear on
the TV screen once you load the disc.
1 Load one of the last ten discs.
➜ “LOADING” appears on the TV
screen.
■ To select a playback feature or item
Use 2 / 3/5/a or the numeric
buttons (0-9), and then press ENTER to
start playback.
2 Press 3/8 while “LOADING” is
displayed on the TV screen.
➜ “RESUME PLAY” appears on the TV
screen and the disc is played back from
the last point.
■ To access or exit from the menu
Press MENU.
■ To cancel the resume mode
When playback is stopped, press
7
again.
16 En
Playback Operation
■ Title/Chapter/Track selection
Using the on-screen display (OSD)
(DVD/VCD)
The OSD menu shows disc playback
information (e.g., the title or chapter number,
elapsed playing time or audio/subtitle
language). A number of operations are
possible without interrupting disc playback.
1 Press 5/a to select [TITLE] or
[CHAPTER] (DVD) or [TRACK] (VCD).
2 Press ENTER.
3 Select a title, chapter or track number using
the numeric buttons (0-9).
1 During playback, press ON SCREEN.
➜ A list of available disc information
appears on the TV screen.
■ Time search (DVD/VCD)
1 Press 5/a to select [TT TIME] / [CH
TIME] (DVD) or [TRACK TIME] / [DISC
TIME] (VCD).
DVD
MENU
TITLE
02/14
02/14
5.1CH
ENG
•
[TT TIME] refers to the total time of
the current title, and [CH TIME] refers
to the total time of the current chapter.
CHAPTER
AUDIO
SUBTITLE
BITRATE 16
TITLE ELAPSED 0:02:25
2 Press ENTER.
3 Enter hours, minutes and seconds from left
to right using the numeric buttons (0-9)
(e.g. 0:34:27).
VCD/SVCD
MENU
TRACK
02/14
■ Audio/Subtitle/Angle selection
(DVD)
You can change [AUDIO], [SUBTITLE] or
[ANGLE] if these functions are available on
the disc you are playing.
DISC TIME
TRACK TIME
REPEAT
0:49:17
0:03:43
OFF
BITRATE 16
TOTAL ELAPSED 0:02:25
2 Press 5/a to scroll the information, and
then press ENTER to access the selected
item.
1 Press 5/a to select [AUDIO],
[SUBTITLE] or [ANGLE].
2 Press ENTER.
3 Use the numeric buttons (0-9) to input
the number/time or press 5/a to make a
selection, and then press ENTER.
3 For Audio and Subtitle:
Press 5/a to highlight your selection, and
then press ENTER.
➜ Playback changes to the selected time
or to the selected title/chapter/track.
OR
For Angle:
Select an angle using the numeric
buttons (0-9).
17 En
Playback Operation
■ Repeat/Time Display (DVD/VCD)
Special VCD/SVCD features
1 Press 5/a to select [REPEAT] or [TIME
DISP.].
Using the playback control (PBC)
menu
2 Press ENTER.
3 Press 5/a to highlight your selection, and
then press ENTER.
For a VCD with a playback control (PBC)
feature (version 2.0 only)
■ Time display (CD)
1 Press MENU to toggle between “PBC ON”
and “PBC OFF”.
Each time you press ON SCREEN, the
➜ If you select “PBC ON”, the disc menu
appears (if available) on the TV screen.
time display changes as follows:
TOTAL ELAPSED
SINGLE REMAIN
TOTAL REMAIN
2 Use the numeric buttons (0-9) to select
SINGLE ELAPSED
a playback option.
•
Press l22 / 33l to move to the
previous/next page (if available).
3 During playback, press TOP MENU/
RETURN to return to the menu screen.
Special DVD features
Playing by title
■ To skip the index menu and play
back a disc from the beginning
1 Press MENU.
Press MENU to turn off the PBC function.
➜ The disc title menu appears on the TV
screen.
2 Use 2 / 3/5/a or the numeric
Playing data discs
(MP3/WMA/JPEG/DivX)
buttons (0-9) to select a playback option.
3 Press ENTER.
1 Load a data disc.
Selecting an audio language/
format and subtitle language
•
The disc reading time may exceed 30
seconds due to the complexity of the
directory/file configuration.
■ To select an audio language/format
➜ The data disc menu appears on the TV
Press AUDIO repeatedly to select an audio
language and/or format.
screen.
00:00 00:00
001/020
■ To select a subtitle language
Favorite
Press SUBTITLE repeatedly to select a
subtitle language.
MP3
Piano
Cello
MP3
MP3
MP3
Jazz
Live
18 En
Playback Operation
2 Playback starts automatically. If not, press
3/8 .
Using the preview function
This function displays the content of the
current folder or the entire disc.
3 Press l22 / 33l to select another track/file
in the current folder.
1 Press
7
during playback.
➜ 12 thumbnails appear on the TV screen.
Notes
•
•
•
It may not be possible to play certain MP3/
WMA/JPEG/DivX discs due to the configuration
and characteristics of the discs or the recording
conditions.
HD JPEG images may not be displayed correctly
when the first image is displayed or the disc is
ejected. For details about HD JPEG, see “HD
JPEG” on page 31.
Depending on the picture size, HD JPEG images
may appear smaller in size.
2 Press l22 / 33l to display the other
thumbnails on the previous/next page.
Selecting a folder and track/file
3 Use 2 / 3/5/a to highlight one of the
1 Press 5/a to select a folder, and then
press ENTER to open the folder.
thumbnails, and then press ENTER to start
playback.
2 Press 5/a to select a track/file.
OR
3 Press ENTER.
Move the cursor to highlight
bottom of the page to start playback from
the first thumbnail on the current page.
on the
➜ Playback starts from the selected file to
the end of the folder.
■ For JPEG
Special picture disc features
4 Press MENU to return to the JPEG disc
menu.
1 Load a picture disc (JPEG, Kodak Picture
CD or Fujicolor CD).
Zooming pictures in/out
➜ For JPEG, the picture menu appears on
the TV screen.
➜ For Kodak Picture CD and Fujicolor
CD, the slideshow begins.
1 During playback, press ZOOM repeatedly
to display the picture at different scales.
2 Use 2 / 3/5/a to pan through the
enlarged picture.
■ For JPEG
2 Press 3/8 to start the slideshow.
19 En
Playback Operation
Playback with multi-angles
Special DivX features
During playback, press 2 / 3/5/a to
rotate the picture on the TV screen.
DivX files including DMF (DivX Media
Format) features only
2: rotates the picture counter-clockwise
3: rotates the picture clockwise
5: flips the picture vertically
Using the interactive menu
1 Load a disc.
a: flips the picture horizontally
➜ The interactive menu appears on the
TV screen.
Note
2 Use 2 / 3/5/a to select a chapter.
For HD JPEG, the 5/a key is not available.
3 Press ENTER or 3/8 to start playback of
Playing MP3 music and JPEG
pictures simultaneously
the selected chapter.
■ To access the interactive menu
During playback, press MENU.
1 Load a disc that contains both MP3 music
and JPEG picture data.
➜ The disc menu appears on the TV
screen.
■ To return to the data disc menu
screen
When the interactive menu is displayed,
2 Select an MP3 music track.
press
7
.
3 During MP3 music playback, select a
JPEG picture file from the TV screen, and
then press 3/8 .
Selecting an audio/subtitle language
■ To select an audio language
➜ The picture files are played back one
after another until the end of the folder.
During playback, press AUDIO to switch
the audio language recorded on the
contents.
4 To quit simultaneous playback, press
MENU, and then press
7
.
■ To select a subtitle language
Notes
During playback, press SUBTITLE to
switch or turn on/off the subtitle language
recorded on the contents.
•
Some files cannot be played correctly depending
on disc characteristics or recording conditions.
This function is not available when [HD JPEG] is
set to [ON] (see page 31).
•
Note
For information about external subtitle files, see
“Displaying DivX external subtitle files” on
page 33.
20 En
Playback Operation
Playing data files
Using a USB device
Yamaha and suppliers accepts no liability for
the loss of data saved on the USB devices
connected to this unit. As a precaution, it is
recommended that the files are tested after
they have been saved on.
You can play back MP3, WMA, JPEG and
DivX files saved on your supported USB
device.
Supported USB devices
1 Connect your USB device to the USB port
of this unit (see “USB port” on page 11).
➜ “Press USB mode key to switch device”
appears on the TV screen.
This unit supports USB mass storage class
devices (e.g., flash memories, card readers,
portable audio players) using FAT16 or FAT32
format.
2 Press USB.
Notes
•
The reading time may exceed 30 seconds
due to the number of files/folders.
The file menu appears on the TV screen.
•
Some devices may not work properly even if they
meet the requirements.
➜
•
If “Device not supported” appears on the TV
screen when you connect the USB device, follow
the procedure below.
3
Follow the procedure in “Playing data discs
(MP3/WMA/JPEG/DivX)” on page 18.
– Set this unit to the standby mode, and then turn
it on again.
– Disconnect the device when this unit is in the
standby mode, then connect it again and turn
on this unit.
– Connect the AC adapter if the adapter is
supplied with the device.
If “Device not supported” appears even after you
perform this procedure, the device is not playable
with this unit.
If “USB current protection active. Device not
supported” appears on the TV screen, the device
is not playable with this unit because the power
consumption of the device is too high.
This unit cannot read more than two card reader
slots at once, though it can recognize up to six
slots. The first slot has priority.
■ To exit from the USB mode
Press
USB.
7
to stop playback, and then press
Notes
•
You cannot access the USB mode while
“LOADING” is displayed on the TV screen.
If you disconnect the USB device or open the disc
tray of this unit, the playback mode is
automatically switched to the disc mode.
For DivX, this unit is compatible with a bit rate
range of 3 Mbps or less.
•
•
•
•
•
Some files may not work properly depending on
the USB device specification.
– For DivX, the video may freeze shortly or the
sound may break in the segments.
•
•
For an external hard disk drive, this unit is
compatible with size of 80 GB or less.
Do not connect devices other than USB mass
storage class devices: USB chargers, USB hubs,
PCs, etc.
For MP3, the sound may break in the segments
during MP3/JPEG simultaneous playback.
In this case, record the file at a lower bit rate
and/or smaller size so that the file may work
properly.
•
•
Copyright-protected files cannot be played.
This unit can display up to 648 files. However,
less than 648 files may be displayed if some files
are not playable with this unit.
•
•
If the USB device is partitioned, only the first
partition is displayed.
This unit can play back files of 4 GB in size or
less.
21 En
Setup Menu
Setup Menu
LOCK
Setup is carried out on the TV screen, enabling
you to customize this unit to suit your own
particular requirements.
Select this to lock playback of the current disc.
Subsequent access to a locked disc requires a
six-digit password.
Notes
The default password is “000 000” (see
“Changing the password” on page 34).
•
Unless stated otherwise, all operations described
here are carried out using the supplied remote
control.
UNLOCK
Select this to unlock the disc and allow future
playback.
•
•
To return to the previous menu, press 2.
To exit from the menu, press SET UP.
2 Press 5/a to select a setting, and then
press ENTER.
General setup menu
Dimming the front panel display
1 Press SET UP.
You can select different levels of brightness
for the front panel display.
2 Press 2 / 3 to select “GENERAL SETUP
PAGE”.
1 In “GENERAL SETUP PAGE”, press
5/a to highlight [DISPLAY DIM], and
then press 3.
3 Press ENTER.
100%
GENERAL SETUP PAGE
Select this for full brightness.
DISC LOCK
70%
DISPLAY DIM
PROGRAM
Select this for medium brightness.
OSD LANGUAGE
SCREEN SAVER
SLEEP
40%
Select this for dimming display.
AUTO STANDBY
DIVX(R) VOD CODE
2 Press 5/a to select a setting, and then
press ENTER.
Locking/Unlocking the disc for
viewing
Programming disc tracks
(except MP3/WMA/JPEG/DivX)
Not all discs are rated or coded by the
manufacturer of the disc. You can prevent
playback of a specific disc by locking the disc.
You can lock up to 40 discs on this unit.
You can play back the contents of a disc in the
desired order by programming the tracks to be
played. You can store up to 20 tracks per disc
with a maximum of ten discs.
1 In “GENERAL SETUP PAGE”, press
5/a to highlight [DISC LOCK], and then
press 3.
1 In “GENERAL SETUP PAGE”, press
5/a to highlight [PROGRAM], and then
press 3 to select [INPUT MENU].
22 En
Setup Menu
2 Press ENTER.
■ To start program playback
➜ The input menu appears on the TV
8 Use 2 / 3/5/a to highlight [START] on
the program menu, and then press
ENTER.
screen.
PROGRAM: TRACK (01-17)
➜ Playback starts for the selected tracks in
the programmed sequence.
6
7
8
9
_ _
_ _
_ _
_ _
1
2
3
4
5
04
10
_ _
_ _
_ _
■ To exit from program playback
10 _ _
START
9 Use 2 / 3/5/a to highlight [EXIT] on
the program menu, and then press
ENTER.
EXIT
NEXT
■ To input your favorite tracks/
chapters
OSD language
3 Use the numeric buttons (0-9) to enter a
This menu contains various options for the on-
screen display (OSD) language. For details,
see “Setting the OSD Language” on page 14.
valid track/chapter number.
4 Use 2 / 3/5/a to move the cursor to the
next position.
•
If the track/chapter number is more
than ten, press 33l to move to the next
page, and then proceed with
programming.
Setting the screen saver
This function is used to turn on or off the
screen saver.
1 In “GENERAL SETUP PAGE”, press
5/a to highlight [SCREEN SAVER], and
then press 3.
OR
•
Use 2 / 3/5/a to highlight [NEXT]
on the program menu, and then press
ENTER.
ON
Select this to turn off the TV screen when disc
playback is stopped or paused for more than
15 minutes.
5 Repeat steps 3-4 to input another track/
chapter number.
OFF
■ To remove a track
Select this to disable the screen saver function.
6 Use 2 / 3/5/a to move the cursor to the
track you want to remove.
2 Press 5/a to select a setting, and then
press ENTER.
7 Press ENTER to remove this track from
the program menu.
23 En
Setup Menu
®
Setting the sleep timer
Displaying the DivX VOD
registration code
This feature automatically sets this unit to the
standby mode after a certain elapsed period.
®
Yamaha provides you with a DivX VOD
(Video On Demand) registration code that
allows you to rent and purchase videos using
1 In “GENERAL SETUP PAGE”, press
5/a to highlight [SLEEP], and then
press 3.
®
the DivX VOD service.
For more information, visit https://
vod.divx.com/.
2 Press 5/a to select a setting.
•
You can select from 30, 60, 90, 120 and
150 minutes. Select [OFF] to cancel the
sleep timer function.
1 In “GENERAL SETUP PAGE”, press
5/a to highlight [DIVX(R) VOD CODE],
and then press 3.
3 Press ENTER.
➜ The registration code appears.
2 Press ENTER to exit.
Setting the auto standby function
This function is used to turn the auto standby
mode on or off when disc playback is stopped
for more than 30 minutes.
Notes
•
To purchase or rent the videos from DivX® VOD
registration code and download the video onto a
CD-R for playback on this unit.
1 In “GENERAL SETUP PAGE”, press
5/a to highlight [AUTO STANDBY],
and then press 3.
•
•
All of the downloaded videos from DivX® VOD
can only be played back on this unit.
For DivX, the time search feature is not available.
ON
Select this to set this unit to the standby mode
automatically when disc playback is stopped
or paused for more than 30 minutes.
OFF
Select this to disable the auto standby
function.
2 Press 5/a to select a setting, and then
press ENTER.
24 En
Setup Menu
Setting the digital output
The [DIGITAL AUDIO] options are:
Audio setup menu
1 Press SET UP.
[DIGITAL OUTPUT] and [LPCM OUTPUT].
2 Press 2 / 3 to select “AUDIO SETUP
1 In “AUDIO SETUP PAGE”, press 5/a to
highlight [DIGITAL AUDIO], and then
press 3.
PAGE”.
3 Press ENTER.
2 Press 5/a to highlight an option.
3 Press 3 to open a submenu.
AUDIO SETUP PAGE
DIGITAL OUTPUT
Set the digital output according to your
optional audio component connections.
ANALOG OUTPUT
DIGITAL AUDIO
HDMI AUDIO
NIGHT MODE
LIP SYNC
OFF
Select this to turn off the digital output.
ALL
Select this if you have connected the digital
audio output jack to a multi-channel decoder/
receiver.
Setting the analog output
Set the analog output to match the playback
capability of this unit.
MPEG ➜ PCM
Select this if your receiver is not capable of
decoding MPEG audio signals.
1 In “AUDIO SETUP PAGE”, press 5/a to
highlight [ANALOG OUTPUT], and then
press 3.
PCM ONLY
Select this only if your receiver is not capable
of decoding multi-channel audio signals.
STEREO
LPCM OUTPUT
Select this to change channel output to stereo,
which only delivers sound from the two front
speakers.
Select this if you have connected this unit to a
PCM-compatible receiver via a digital
terminal, such as the coaxial terminal. In this
case, you may need to adjust [LPCM
OUTPUT].
Discs are recorded at a certain sampling rate.
The higher the sampling rate, the better the
sound quality.
LT/RT
Select this if this unit is connected to a Dolby
Pro Logic decoder.
2 Press 5/a to select a setting, and then
press ENTER.
25 En
Setup Menu
48KHz
•
•
When [DIGITAL OUTPUT] is set to [OFF] on
this unit, HDMI audio is muted even if [HDMI
AUDIO] is set to [ON] and an HDMI connection
is established between the monitor and receiver.
When [DIGITAL OUTPUT] is set to [ALL] on
this unit, PCM signals are still output if the
monitor and receiver only support the PCM
format. However, the audio output is muted when
audio format plays back the DTS source.
Select this to play back discs recorded at the
sampling rate of 48 kHz. All 96 kHz PCM data
streams (if available) are converted to the
sampling rate of 48 kHz.
96KHz
Select this to play back discs recorded at the
sampling rate of 96 kHz. If the 96 kHz disc is
copy protected, the digital output is
automatically converted to the sampling rate of
48 kHz.
Turning the night mode on/off
In the night mode, high volume output is
softened and low volume output is brought
upward to an audible level. It is useful when
you want to watch your favorite action movie
without disturbing others at night.
4 Press 5/a to select a setting, and then
press ENTER.
Turning the HDMI audio on/off
When you connect this unit to an HDMI
compatible component via the HDMI jack,
select to turn on or off the HDMI audio output.
1 In “AUDIO SETUP PAGE”, press 5/a
to highlight [NIGHT MODE], and then
press 3.
1 In “AUDIO SETUP PAGE”, press 5/a to
highlight [HDMI AUDIO], and then
press 3.
ON
Select this to level out the volume. This
feature is only available for movies with the
Dolby Digital mode.
ON
Select this to turn on the HDMI audio output.
OFF
OFF
Select this when you want to enjoy the full
dynamic range of surround sound.
Select this to turn off the HDMI audio output.
2 Press 5/a to select a setting, and then
press ENTER.
Notes
•
If you are not using the HDMI audio output, set
this to [OFF].
•
If the monitor/receiver connected to this unit
using HDMI does not support HDMI audio signal
input, set this to [OFF].
•
•
This unit can output the following audio signals
using HDMI: 32/44.1/48 kHz, 2ch linear PCM
signals and bitstream signals (Dolby Digital, DTS
and MPEG).
When audio signals are being output by HDMI-
compatible components, digital output signals are
muted.
26 En
Setup Menu
Setting the lip synchronization
TV type
This feature allows you to delay the sound
output in order to synchronize it with the
This menu contains the options for selecting
the color system that matches your TV. For
video image. This may be necessary when you details, see “Setting a color system for your
use certain LCD monitors or projectors.
TV” on page 13.
1 In “AUDIO SETUP PAGE”, press 2 / 3
to highlight [LIP SYNC], and then
press 3.
2 Press 2 / 3 to adjust the delay time
(between 00 ms and 200 ms), and then
press ENTER.
Setting the TV display
Set the aspect ratio of this unit to match your
TV. The format you select must be available
on the disc. Otherwise, the TV display setting
will not affect the picture during playback.
1 In “VIDEO SETUP PAGE”, press 5/a
to highlight [TV DISPLAY], and then
press 3.
Video setup menu
2 Press 5/a to highlight one of the
1 Press SET UP.
following options.
2
Press 2 / 3 to select “VIDEO SETUP
PAGE”.
4:3 PAN SCAN
Select this if the aspect ratio of your TV is 4:3
and you want both sides of the picture to be
trimmed or formatted to fit your TV screen.
3 Press ENTER.
4:3 LETTER BOX
VIDEO SETUP PAGE
Select this if the aspect ratio of your TV is 4:3.
In this case, a wide picture with black bands
on the upper and lower portions of the TV
screen are displayed.
TV TYPE
TV DISPLAY
PROGRESSIVE
PICTURE SETTING
BLACK LEVEL
CLOSED CAPTION
HDMI SETUP
16:9
Select this if you have a widescreen TV.
3 Select an item, and then press ENTER.
27 En
Setup Menu
■ The relationship between the setting
Turning the progressive scan
function on/off
This feature is only available if you have
connected this unit to a progressive scan TV
through the component video jacks (see
“Component video jacks <A>” on page 9).
of this unit and the TV display
When the aspect ratio of your TV is 4:3:
Playback
disc
TV display
Setting
16:9
1
*
1 In “VIDEO SETUP PAGE”, press 5/a
to highlight [PROGRESSIVE], and then
press 3.
4:3 PAN
SCAN
4:3
16:9
4:3
OFF
Select this to disable the progressive scan
function.
4:3 LETTER
BOX
ON
Select this to enable the progressive scan
function.
2 Press 5/a to select a setting, and then
press ENTER.
When the aspect ratio of your TV is 16:9
(widescreen):
Notes on activating progressive scan:
• Ensure that your TV is equipped with
progressive scan.
Playback
TV display
Setting
disc
• Connect using a component video cable.
• When making HDMI connections, you
cannot select [PROGRESSIVE].
16:9
16:9
4:3
2
*
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE
*1: If the disc is not assigned to playback in
panscan, it is played in letterbox.
*2: The side of the picture may be stretched
DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE
USER SWITCH THE CONNECTION TO THE
“STANDARD DEFINITION” OUTPUT. IF THERE
ARE QUESTIONS REGARDING OUR VIDEO
MONITOR COMPATIBILITY WITH THIS MODEL
525P AND 625P DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.
This unit is compatible with the complete line of
Yamaha products, including the projectors
DPX-1300, DPX-830 and the plasma monitor
PDM-4220.
depending on the TV. In this case, check the
screen size and aspect ratio of your TV.
28 En
Setup Menu
BRIGHTNESS
Adjusting picture settings
Increase or decrease the value to brighten or
dim the picture. Zero (0) is the average
brightness setting value.
This unit comes with three predefined sets of
picture color settings and one personal setting
that you can define yourself.
CONTRAST
Increase or decrease the value to sharpen or
dull the picture. Zero (0) is the average contrast
setting value.
1 In “VIDEO SETUP PAGE”, press 5/a to
highlight [PICTURE SETTING], and then
press 3.
STANDARD
Select this for the standard picture setting.
TINT
Increase or decrease the value to darken or
lighten the picture. Zero (0) is the average tint
setting value.
BRIGHT
Select this to make the TV picture brighter.
COLOR
SOFT
Increase or decrease the value to enhance or
fade the picture. Zero (0) is the average color
setting value.
Select this to make the TV picture softer.
PERSONAL
Select this to personalize your picture color by
adjusting the brightness, contrast, tint and
color (saturation).
5 Press 2 / 3 to adjust the setting that best
suits your personal preference.
6 Repeat steps 4-5 to adjust other color
2 Press 5/a to select a setting, and then
press ENTER.
features.
7 Press ENTER.
3 If you select [PERSONAL] in step 1,
proceed to steps 4-7.
Note
➜ The “PERSONAL PICTURE SETUP”
menu appears.
All picture settings are not available for HDMI
output.
Turning the black level on/off
PERSONAL PICTURE SETUP
If [TV TYPE] is set to [NTSC] (see page 13),
set the black level to on to improve the color
contrast during playback. The black level
setting has no effect if [TV TYPE] is set to
[PAL].
BRIGHTNESS
CONTRAST
TINT
0
0
0
0
COLOR
1 In “VIDEO SETUP PAGE”, press 5/a
to highlight [BLACK LEVEL], and then
press 3.
4 Press 5/a to select one of the following
options.
ON
Select this to enhance the black level.
OFF
Select this for the standard black level setting.
2 Press 5/a to select a setting, and then
press ENTER.
29 En
Setup Menu
WIDE SCREEN FORMAT
Turning the closed caption on/off
Set the aspect ratio of the projected images on
the screen. This feature is only available when
making HDMI connections and [TV
DISPLAY] is set to [16:9] (see page 27).
Closed captions are data hidden in the video
signals of specific discs and are invisible
without the use of a special decoder. The
difference between subtitles and captions is
that subtitles are intended for hearing persons
and captions are for the hearing impaired.
Subtitles rarely show all of the audio. For
example, captions show sound effects (e.g.,
“phone ringing”, “footsteps”), while subtitles
do not.
SUPERWIDE
Select to display a 4:3 image on the 16:9 screen
with non-linear stretching (center position of
screen is stretched less than the sides). This
feature is not available when the resolution is
480p or 576p.
4:3 PILLAR BOX
Before you select this function, ensure that the
disc contains closed caption information and
your TV also supports this function.
Select to display a 4:3 image on the 16:9 screen
without stretching. When playing a disc recorded
in the 16:9 image, the image is displayed in its
original aspect ratio (16:9) without pillar boxes.
1 In “VIDEO SETUP PAGE”, press 5/a to
highlight [CLOSED CAPTION], and then
press 3.
OFF
No aspect ratio adjustment is made when this
option is selected.
ON
Select this to enable the closed caption
function.
HDMI VIDEO
Set the resolution depending on the monitor
you are using.
OFF
Select this to disable the closed caption
function.
480P
480 progressive-scan video
2 Press 5/a to select a setting, and then
press ENTER.
576P
576 progressive-scan video
720P
720 progressive-scan video
Setting the HDMI video
1080I
1080 interlace video
When you connect this unit to an HDMI
compatible component via the HDMI jack,
select the following video output settings
depending on the connected component.
AUTO
The resolution is automatically selected to
match the monitor you are using.
1 In “VIDEO SETUP PAGE”, press 5/a
to highlight [HDMI SETUP], and then
press 3.
2 Press 5/a to highlight an option.
3 Press 3 to enter a submenu.
30 En
Setup Menu
Notes
Preference setup menu
•
For settings other than [AUTO], HDMI video
1 Press
7
twice to stop playback
(if necessary), and then press SET UP.
signals may not be output properly if a resolution
output setting is not supported by the HDMI
component you are using. In that case, follow the
steps below to return to the initial setting.
2 Press 2 / 3 to select “PREFERENCE
PAGE”.
1 Press OPEN/CLOSE (
to open the disc tray.
2 Press 2.
3 Press SUBTITLE.
Do not perform this operation while playing back
) on the front panel
3 Press ENTER.
PREFERENCE PAGE
a disc on this unit.
You cannot set [TV TYPE] and
[PROGRESSIVE] when making HDMI
connections.
AUDIO
SUBTITLE
DISC MENU
PARENTAL
VR LIST
•
•
When disconnecting the HDMI cable, the setting
of [TV TYPE] may be changed. If the component
video, S-video or composite video signal is not
output correctly, see “Troubleshooting” on
page 36 to set the correct TV type again.
MP3/JPEG NAV
DIVX SUBTITLE
PBC
Audio, subtitle and disc menu
HD JPEG
These menus contain various language options
for the audio, subtitles and disc menus
recorded on the DVD-Video. For details, see
“Setting the audio, subtitle and disc menu
languages (DVD-Video only)” on page 14.
This unit can display High-Definition JPEG
images when connecting to an HDMI
component.
ON
Displays JPEG pictures with high quality.
OFF
Restricting playback with parental
control
Displays JPEG pictures with standard quality.
Some DVDs may have a parental level
assigned to the complete disc or to certain
scenes on the disc. This feature lets you set a
playback limitation level.
The rating levels are from 1 to 8 and are
country dependent. You can prohibit playback
of certain discs that are not suitable for your
children or play certain discs in alternative
scenes.
Notes
•
You can select [HD JPEG] when the HDMI video
signals with 720p or 1080i are output.
When [HD JPEG] is set to [ON] and HD JPEG
pictures are displayed, video signals other than
HDMI signals are not output.
•
•
You cannot select [HDMI VIDEO] (see page 30)
and [HD JPEG] when HD JPEG pictures are
displayed.
31 En
Setup Menu
1 In “PREFERENCE PAGE”, press 5/a to
highlight [PARENTAL], and then press 3.
Selecting playback of VR format
There are two ways to play back a disc in VR
(Video Recording) format: ORIGINAL and
PLAY LIST. This feature is not available with
non-VR format discs.
PREFERENCE PAGE
AUDIO
1 KID SAFE
2 G
1 In “PREFERENCE PAGE”, press 5/a to
highlight [VR LIST], and then press 3.
ORIGINAL LIST
Select this to play the originally recorded titles
on the disc.
SUBTITLE
DISC MENU
PARENTAL
VR LIST
3 PG
4 PG 13
5 PGR
6 R
MP3/JPEG NAV
DIVX SUBTITLE
PBC
7 NC 17
8 ADULT
PLAY LIST
Select this to play the edited version of the
disc. This feature is only available when a play
list has been created.
2 Press 5/a to highlight a rating level for
the inserted disc, and then press
ENTER.
2 Press 5/a to highlight a setting, and then
press ENTER.
•
To disable parental controls and have
all discs play, select [8 ADULT].
■ To play back a disc in VR format
3 Press SET UP to close the setup menu.
3 Use the numeric buttons (0-9) to enter
the six-digit password (see “Changing the
password” on page 34).
4 Press 3/8 to begin to play back the disc
➜ DVD discs that are rated above the
level you selected do not play unless
you enter your six-digit password.
with the setting you selected.
Selecting the MP3/JPEG menu
MP3/JPEG navigator can be set only if the
disc was recorded with a menu. It allows you
to select different display menus for easy
navigation.
Note
Some DVD discs are not encoded with a rating
though the movie rating may be printed on the disc
cover. The rating level feature does not work for
such discs.
1 In “PREFERENCE PAGE”, press 5/a to
highlight [MP3/JPEG NAV], and then
press 3.
WITHOUT MENU
Select this to display all the files contained in
the MP3/Picture CD.
WITH MENU
Select this to display only the folder menu of
the MP3/Picture CD.
2 Press 5/a to select a setting, and then
press ENTER.
32 En
Setup Menu
Displaying DivX external subtitle
files
The font sets listed below are available for
DivX external subtitle files. This setting
allows you to see the proper font set on-screen
to match the subtitle file.
Notes
•
•
•
Some discs cannot be played depending on disc
characteristics or recording conditions.
Some external subtitle files may be displayed
incorrectly or not at all.
For external subtitle files, the following subtitle
format filename extensions are supported (note
that these files are not shown within the disc
navigation menu): .srt, .sub, .ssa, .smi
The filename of the movie file has to be repeated
at the beginning of the filename for the external
subtitle file.
1 In “PREFERENCE PAGE”, press 5/a to
highlight [DIVX SUBTITLE], and then
press 3.
•
•
GROUP1:
Albanian (sq), Basque (eu), Catalan (ca),
Danish (da), Dutch (nl), English (en),
Faroese (fo), Finnish (fi), French (fr),
German (de), Icelandic (is), Irish (ga),
Italian (it), Norwegian (no),
The number of external subtitle files that can be
switched for the same movie file is limited to a
maximum of ten.
Selecting the PBC (playback
control) function
Portuguese (pt), Rhaeto-Romanic (rm),
Scottish (gd), Spanish (es), Swedish (sv)
You can set playback control (PBC) to on or
off. This function is available only on Video
CD 2.0 with the playback control (PBC)
feature.
GROUP2:
Albanian (sq), Croatian (hr), Czech (cs),
Hungarian (hu), Polish (pl), Romanian (ro),
Slovak (sk), Slovenian (sl)
1 In “PREFERENCE PAGE”, press 5/a to
highlight [PBC], and then press 3.
GROUP3:
Bulgarian (bg), Byelorussian (be),
Macedonian (mk), Russian (ru), Serbian (sr),
Ukrainian (uk)
ON
Select this to display a disc menu.
OFF
GROUP4:
Select this to not display a disc menu.
Playback starts from the beginning of a disc.
Hebrew (iw), Yiddish (ji)
GROUP5:
Turkish (tr)
2 Press 5/a to select a setting, and then
press ENTER.
2 Press 5/a to select a group, and then
press ENTER.
Note
You can also use the MENU button on the remote
control to turn on or off the playback control (PBC)
function (see “Using the playback control (PBC)
menu” on page 18).
33 En
Setup Menu
4 Enter the new six-digit password.
Changing the password
5 Enter the new six-digit password again to
The same password is used for both parental
control and disc lock. Enter your six-digit
password when prompted on the screen. The
default password is 000 000.
confirm the password.
6 Press ENTER to confirm your new
password.
➜ The new six-digit password is now
1 In “PREFERENCE PAGE”, press 5/a to
highlight [PASSWORD], and then press 3
to select [CHANGE].
valid.
Resetting the system
You can reset all options and your personal
settings to the initial factory settings,
excluding your password for [PARENTAL]
and [DISC LOCK].
PREFERENCE PAGE
SUBTITLE
DISC MENU
PARENTAL
VR LIST
1 In “PREFERENCE PAGE”, press 5/a to
highlight [DEFAULT], and then press 3
to select [RESET].
MP3/JPEG NAV
DIVX SUBTITLE
PBC
PASSWORD
CHANGE
2 Press ENTER.
➜ All settings are reset to the initial
2 Press ENTER to enter the “Password
factory settings.
Change Page”.
OLD PASSWORD
NEW PASSWORD
CONFIRM PWD
OK
3 Use the numeric buttons (0-9) to enter
your old six-digit password.
•
When doing this for the first time, enter
“000 000”.
•
If you forget your old six-digit
password, enter “000 000”.
34 En
Language Codes
Language Codes
These codes can be used to select other languages. This does not affect the options in
“AUDIO”, “SUBTITLE” or “DISC MENU”.
Abkhazian
Afar
6566 Gaelic
6565 Gallegan
6570 Georgian
8381 German
6577 Gikuyu
6582 Greek
7168 Macedonian
7176 Malagasy
7565 Malay
7775 Sardinian
7771 Scottish Gaelic
7783 Serbian
7776 Shona
8367
7168
8382
8378
8368
8373
8375
8376
8379
8384
7882
6983
8385
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
Afrikaans
Albanian
Amharic
Arabic
6869 Malayalam
7573 Maltese
7784 Sindhi
6976 Manx
7186 Sinhalese
7773 Slovak
Armenian
Assamese
Avestan
Aymara
Azerbaijani
Bashkir
7289 Guarani
6583 Gujarati
6569 Hausa
7178 Maori
7185 Marathi
7782 Slovenian
7772 Somali
7779 Sotho, Southem
7778 South Ndebele
7865 Spanish
7886 Sundanese
7886 Swahili
7868 Swati
7265 Marshallese
7269 Moldavian
7290 Mongolian
7273 Nauru
6589 Hebrew
6590 Herero
6665 Hindi
Basque
6985 Hiri Motu
6669 Hungarian
6678 Icelandic
6672 Ido
7279 Navaho
Belarusian
Bengali
7285 Navajo
7383 Ndebele, North
7379 Ndebele, South
7368 Ndonga
Bihari
7882 Swedish
7871 Tagalog
7869 Tahitian
8369 Tajik
Bislama
Bokmål, Norwegian
Bosnian
Breton
6673 Indonesian
7866 Interlingua (International) 7365 Nepali
6683 Interlingue
6682 Inuktitut
6671 Inupiaq
7789 Irish
7369 Northern Sami
7385 North Ndebele
7375 Norwegian
7165 Norwegian Bokmål
7384 Norwegian Nynorsk
7465 Nyanja
7868 Tamil
Bulgarian
Burmese
Castilian
Catalan
7879 Tatar
7866 Telugu
7878 Thai
6983 Italian
6765 Japanese
6772 Javanese
6769 Kalaallisut
7889 Kannada
7889 Kashmiri
9072 Kazakh
9065 Khmer
7889 Tibetan
7878 Tigrinya
Chamorro
Chechen
Chewa
7486 Nynorsk, Norwegian
7576 Occitan (post 1500)
7578 Old Bulgarian
7583 Old Church Slavonic
7575 Old Slavonic
7577 Oriya
7967 Tonga (Tonga Islands) 8479
6785 Tsong
6785 Tswana
6785 Turkish
7982 Turkmen
7977 Twi
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9065
9085
Chichewa
Chinese
Chuang
Church Slavic
Church Slavonic
Chuvash
Cornish
6785 Kikuyu
7573 Oromo
6785 Kinyarwanda
6786 Kirghiz
7587 Komi
8287 Ossetian
7983 Uighur
7983 Ukrainian
8073 Urdu
8065 Uzbek
7065 Vietnamese
8076 Volapük
8084 Walloon
7967 Welsh
8083 Wolof
8185 Xhosa
8277 Yiddish
8279 Yoruba
8278 Zhuang
8285 Zulu
7589 Ossetic
7586 Pali
Corsican
Croatian
Czech
6779 Korean
7579 Panjabi
7282 Kuanyama
6783 Kurdish
6865 Kwanyama
7876 Lao
7574 Persian
7585 Polish
Danish
7574 Portuguese
7679 Provençal
7665 Pushto
Dutch
Dzongkha
English
6890 Latin
6978 Latvian
6979 Letzeburgesch
6984 Limburgan
7079 Limburger
7074 Limburgish
7073 Lingala
7082 Lithuanian
7089 Luxembourgish
7686 Quechua
Esperanto
Estonian
Faroese
7666 Raeto-Romance
7673 Romanian
7673 Rundi
Fijian
7673 Russian
Finnish
7678 Samoan
8377
French
7684 Sango
8371
Frisian
7666 Sanskrit
8365
35 En
Troubleshooting
Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are
experiencing is not listed below or if the instruction below does not help, set this unit to the
standby mode, disconnect the power cable, and contact the nearest authorized Yamaha
dealer or service center.
Problem
Solution
Connect the AC power cable properly.
No power
No picture
Press STANDBY/ON on the front panel to turn on the power.
Refer to the manual supplied with your TV to select the video input
channel correctly. Change the TV channel until you see the DVD
screen.
Turn on your TV.
Check the video connection.
Video signals other than HDMI signals are not output when HD JPEG
pictures are displayed (see “HD JPEG” on page 31).
No picture is displayed when
you make HDMI connections
(using the HDMI jacks)
Follow the steps below to change the [HDMI VIDEO] to [AUTO].
1. Press OPEN/CLOSE (
) on the front panel or press and hold
7
on the remote control to open the disc tray.
2. Press 2 on the remote control.
3. Press SUBTITLE on the remote control.
No picture is displayed when
you do not use progressive
scan connections (using the
component video jacks)
Follow the steps below to turn off the progressive scan.
1. Press OPEN/CLOSE (
) on the front panel or press and hold
7
on the remote control to open the disc tray.
2. Press 2 on the remote control.
3. Press ZOOM on the remote control to deactivate the progressive
scan.
Completely distorted picture or Check that the disc is compatible with this unit (see “Playable disc
black/white picture or no
picture
formats” on page 3).
Check that the TV type of this unit is set to match that of the disc and
your TV (see “Setting a color system for your TV” on page 13). Follow
the steps below to change the setting of [TV TYPE].
1. Press OPEN/CLOSE (
) on the front panel or press and hold
7
on the remote control to open the disc tray.
2. Press 3 on the remote control.
3. Press AUDIO on the remote control.
Distorted picture
Occasionally, a small amount of picture distortion may appear
depending on the disc being played back. This is not a malfunction.
The screen size looks
unnatural, or the caption is
displayed only partially on the
TV monitor or is not displayed
at all
Check that the TV setting of this unit matches the screen size of your
TV (see “Setting the TV display” on page 27).
Change the screen size and the aspect ratio of your TV.
36 En
Troubleshooting
Problem
Solution
No sound or distorted sound
Adjust the volume.
Check that the speakers are connected correctly.
For MP3/WMA, check that the sampling rate and bit rate are
compatible with this unit (see “Specifications” on page 41).
No audio at digital output
Check the digital connections.
If you are playing a DTS source, check that your receiver can decode
DTS, and that [DIGITAL OUTPUT] is set to [ALL] (see page 25).
If you are playing an MPEG-2 source, check that your receiver can
decode MPEG-2. Otherwise, check that [DIGITAL OUTPUT] is set to
[MPEG ➜ PCM] (see page 25).
Check that the audio format of the selected audio language matches
your receiver capabilities.
Disc does not play
The CD-R/RW, DVD+R/RW/R DL and DVD-R/RW/R DL must be
finalized.
Check that the disc label is facing up.
Check whether the disc is defective by trying another disc.
If you have recorded a JPEG, MP3 or WMA disc yourself, check that
your disc contains at least ten JPEG picture files or five MP3/WMA
music tracks.
For MP3/WMA, check that the sampling rate and bit rate are
compatible. For JPEG, check that the resolution is compatible (see
“Specifications” on page 41).
Check the region code (see “Region codes” on page 3).
Picture freezes momentarily
during playback
Check the disc for fingerprints/scratches and clean it with a soft cloth
wiping from center to edge.
This unit does not respond to
the remote control
Aim the remote control directly at the remote control sensor on the front
panel.
Reduce the distance of the remote control from this unit.
Replace the batteries in the remote control.
Reinsert the batteries with their polarities (+/– signs) as indicated.
Buttons do not work
To completely reset this unit, unplug the AC cord from the AC outlet
for 5-10 seconds.
This unit does not respond to
some operating commands
during playback
Some operations may not be permitted by the disc. Refer to the
instructions of the disc jacket.
The 5/a key is not available during HD JPEG playback.
This unit cannot read CD or
DVD
Use a commonly available CD/DVD lens cleaner to clean the lens
before sending this unit for repair.
37 En
Troubleshooting
Problem
Solution
“NO DISC” appears in the front
panel display
Check that the disc is placed in the disc tray correctly.
“UN DISC” appears in the front
panel display
The disc being loaded is not supported by this unit. Check the disc type
(see “Playable disc formats” on page 3).
Menu items cannot be selected Press
7
twice on the remote control before selecting the setup menu.
Depending on the disc availability, some menu items cannot be
selected.
To select [HD JPEG], check that the HDMI component is connected
correctly and the HDMI video signals with 720p or 1080i are output.
HD JPEG pictures cannot be
displayed
Check that [HD JPEG] is set to [ON] (see page 31).
The disc reading time may exceed 30 seconds.
MP3 music and HD JPEG pictures cannot be played simultaneously.
The audio code may not be supported by this unit.
No sound during DivX movie
playback
The USB device cannot be
recognized
Check that the USB device is connected correctly.
Some devices may not work even if they are USB mass storage class
devices.
Set this unit to the standby mode, and then turn it on again.
Disconnect the device when this unit is in the standby mode, then
connect it again and turn on this unit.
Connect the AC adapter if the adapter is supplied with the device.
If “Device not supported” appears on the TV screen, check whether the
device is supported by this unit (see “Supported USB devices” on
page 21).
If “USB current protection active. Device not supported” appears on the
TV screen, the device is not playable with this unit (see page 21).
38 En
Glossary
Glossary
■
Analog
■
DivX Ultra
Sound that has not been converted into numerical
values. Analog sound varies, while digital sound has
specific numerical values. These jacks send audio
through two channels, the left and right.
DivX Ultra Certified products provide enhanced
playback of advanced media features supported by the
DivX Media Format. Key features include interactive
video menus, subtitles, alternate audio tracks, video
tags and chapter points.
■
Aspect ratio
The ratio of vertical and horizontal sizes of a displayed
image. The horizontal vs. vertical ratio of conventional
TVs is 4:3, and that of widescreens is 16:9.
■
DMF (DivX Media Format)
The DivX Media Format supports advanced media
features, adding controls for an interactive media
experience: interactive video menus, chapter points,
multi-language subtitles and alternate audio tracks.
■
Audio output jacks
Jacks on the back of the DVD player that send audio to
another system (TV, Stereo, etc.).
■
Dolby Digital
A surround sound system developed by Dolby
Laboratories containing up to six channels of digital
audio (front left and right, surround left and right, center
and subwoofer).
■
Bit rate
The amount of data used to hold a given length of
music, measured in kilobits per seconds, or kbps. Or,
the speed at which you record. Generally, the higher the
bit rate, or the higher the recording speed, the better the
sound quality. However, higher bit rates use more space
on a Disc.
■
DTS
Digital Theatre Systems. This is a surround sound
system, but it is different from Dolby Digital. The
formats were developed by different companies.
■
Chapter
Sections of a picture or a music piece on a DVD that are
smaller than titles. A title is composed of several
chapters. Each chapter is assigned a chapter number
enabling you to locate the chapter you want.
■
HDMI
HDMI (High-Definition Multimedia Interface) is the
first industry-supported, uncompressed, all-digital A/V
(audio/video) interface. Providing an interface between
any A/V source (such as a set-top box or A/V receiver)
and an audio/video monitor (such as a digital television-
DTV), HDMI supports standard, enhanced or high-
definition video as well as multi-channel digital audio
using a single cable. HDMI transmits all ATSC HDTV
standards and supports 8-channel digital audio, with
bandwidth extra to accommodate future enhancements
and requirements.
When used in combination with HDCP (High-
bandwidth Digital Content Protection), HDMI provides
a secure audio/video interface that meets the security
requirements of content providers and system
operations. For further information on HDMI, visit the
HDMI website at “www.hdmi.org/”.
■
Component video output jacks
Jacks on the back of the DVD player that send high-
quality video to a TV that has component video input
jacks (R/G/B, Y/PB/PR, etc.).
■
Disc menu
A screen display prepared for allowing selection of
images, sounds, subtitles, multi-angles, etc. recorded on
a DVD.
■
Digital
Sound that has been converted into numerical values.
Digital sound is available when you use the digital
audio output jacks. These jacks send audio through
multiple channels, instead of just two channels as
analog does.
■
HDCP
HDCP (High-bandwidth Digital Content Protection)
developed by Intel corporation, is a method to encrypt
digital video and audio data for purpose of content
protection. For further information on HDCP, visit the
HDCP website at “www.digital-cp.com”.
■
DivX
DivX is a popular media technology created by DivX,
Inc. DivX media files contain highly compressed video
with high visual quality while maintaining a relatively
small file size. DivX files can also include advanced
media features like menus, subtitles, and alternate audio
tracks. Many DivX media files are available for
download online, and you can create your own using
your personal content and easy-to-use tools from
DivX.com.
■
HD JPEG
HD (High-Definition) JPEG provides images in their
enhanced resolution via HDMI connection.
39 En
Glossary
■
Interactive menu
■
Region code
Interactive video menus offer unprecedented
convenience and control so you can quickly navigate
between various scenes or bonus features, and select
from audio track and subtitle options.
A system for allowing discs to be played back only in
the region designated beforehand. This unit will only
play discs that have compatible region codes. You can
find the region code of your unit by looking on the
product label. Some discs are compatible with more
than one region (or ALL regions).
■
JPEG
A very common digital still picture format. A still-
picture data compression system proposed by the Joint
Photographic Expert Group, which features small
decrease in image quality in spite of its high
compression ratio.
■
S-video
Produces a clear picture by sending separate signals for
the luminance and the color. You can use S-video only
if your TV has S-video input jack.
■
MP3
■
Surround
A file format with a sound data compression system.
“MP3” is the abbreviation of Motion Picture Experts
Group 1 (or MPEG-1) Audio Layer 3. By using MP3
format, one CD-R or CD-RW can contain about ten
times as much data as a regular CD can.
A system for creating realistic three dimensional sound
fields full of realism by arranging multiple speakers
around the listener.
■
Title
The longest section of a picture or music feature on
DVD, music, etc., in video software, or the entire album
in audio software. Each title is assigned a title number
enabling you to locate the title you want.
■
Parental control
A function of the DVD to limit playback of the disc by
the age of the users according to the limitation level in
each country. The limitation varies from disc to disc;
when it is activated, playback will be prohibited if the
software’s level is higher than the user-set level.
■
Video output jack
Jack on the back of the DVD player that sends video to
a TV.
■
PCM (Pulse Code Modulation)
■
VR (Video Recording) format
A system for converting analog sound signals to digital
signals for later processing, with no data compression
used in conversion.
A format which enables you to create a DVD disc that
can be extensively re-edited.
■
Playback control (PBC)
Refers to the signal recorded on video CDs or SVCDs
for controlling reproduction. By using menu screens
recorded on a Video CD or SVCD that supports PBC,
you can enjoy interactive-type software as well as
software having a search function.
■
Play list
A list of selected titles to be played back in a specific
order. This option is only available with VR format and
must be created beforehand.
■
Progressive scan
It displays all the horizontal lines of a picture at one
time, as a signal frame. This system can convert the
interlaced video from DVD into progressive format for
connection to a progressive display. It dramatically
increases the vertical resolution.
40 En
Specifications
Specifications
PLAYABLE DISC FORMATS
TV STANDARD
• DVD-Video
• Number of lines ............................. PAL: 625, NTSC: 525
• Vertical frequency...................PAL: 50 Hz, NTSC: 60 Hz
• Playback................................ Multistandard (PAL/NTSC)
• DVD-R, DVD-RW, DVD-R DL
• DVD+R, DVD+RW, DVD+R DL
• Video CD, SVCD
• CD
• PICTURE CD
• CD-R, CD-RW
CONNECTIONS
• Video output ..............................RCA/Phono x 1 (yellow)
• S-video output.................................. Mini DIN, 4 pins x 1
• Component video output
•
MP3 (ISO 9660) ................................. fs 32, 44.1, 48 kHz /
96, 128, 256, 320 kbps (CBR only)
Y output....................................RCA/Phono x 1 (green)
PB output.....................................RCA/Phono x 1 (blue)
PR output.......................................RCA/Phono x 1 (red)
• SCART (U.K. and Europe models only)
............................................................ Euroconnector x 1
• Audio output (L+R) ....... RCA/Phono x 1 pair (white/red)
• Digital output
•
WMA...................fs 44.1 kHz, 62–192 kbps (CBR only) /
fs 48 kHz, 128–192 kbps (CBR only)
• DivX
• JPEG............................................. 3072 x 2048 dpi or less
VIDEO PERFORMANCE
Coaxial.................................................. RCA/Phono x 1
(IEC60958 for CDDA, LPCM /
IEC61937 for MPEG 1/2, Dolby Digital, DTS)
HDMI............................................................Type A x 1
• Video (CVBS) output...........................1 Vpp into 75 ohm
• S-Video output ................................Y: 1 Vpp into 75 ohm
C: 0.3 Vpp into 75 ohm
• Component video output.................Y: 1 Vpp into 75 ohm
PB PR: 0.7 Vpp into 75 ohm
• USB..................................................................Type A x 1
• Remote Control
• RGB (Scart) output (U.K. and Europe models only)
..................................................... Y: 0.7 Vpp into 75 ohm
Input........................................... 3.5 mm mini jack x 1
Output........................................ 3.5 mm mini jack x 1
AUDIO FORMAT
CABINET
• Digital
• Dimensions (W x D x H) ....................435 x 310 x 51 mm
(17-1/8 x 12-3/16 x 2 inch)
• Weight..................................Approx. 2.6 kg (5 lbs. 12oz.)
Dolby Digital, DTS, MPEG.............Compressed digital
PCM....................... fs 44.1, 48, 96 kHz / 16, 20, 24 bits
• Analog sound ...........................................................Stereo
POWER SUPPLY
AUDIO PERFORMANCE
• Power inlet
• DA Converter............................................................24 bit
• Signal-Noise (1 kHz) ............................................. 105 dB
• Dynamic range (1 kHz)............................................ 97 dB
• DVD...........................................fs 96 kHz, 2 Hz-44 kHz /
fs 48 kHz, 2 Hz-22 kHz
U.S.A. and Canada models.................AC 120 V, 60 Hz
U.K. and Europe models.....................AC 230 V, 50 Hz
Australia, Asia, Central and South America models
.......................................AC 110-240 V, 50 Hz/60 Hz
Korea model ................................AC 110-240 V, 60 Hz
• Power consumption..................................... Approx. 14 W
• Standby power consumption....................... Less than 1 W
• SVCD.........................................fs 48 kHz, 2 Hz-22 kHz /
fs 44.1 kHz, 2 Hz-20 kHz
• CD, VCD...................................fs 44.1 kHz, 2 Hz-20 kHz
• Distortion and Noise (1 kHz).............................. 0.0035%
LASER
Type
Wave length
MULTIMEDIA APPLICATIONS
Semiconductor laser GaAlAs
650 nm (DVD)
780 nm (VCD/CD)
7 mW (DVD)
10 mW (VCD/CD)
60 degrees
• Connections...................... USB mass storage class device
• Playback formats (USB device)
MP3................................................ fs 32, 44.1, 48 kHz /
96, 128, 256, 320 kbps (CBR only)
WMA................fs 44.1 kHz, 62–192 kbps (CBR only) /
fs 48 kHz, 128–192 kbps (CBR only)
Output Power
Beam divergence
DivX........................................................ 3 Mbps or less
JPEG ......................................... 3072 x 2048 dpi or less
Specifications are subject to change without prior
notice.
41 En
©2007
All rights reserved.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J
A
WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
3139 245 26181
Printed in China
|